Αρχική Σελίδα
Προϊόντα
Σχετικά με εμάς
Γύρος εργοστασίων
Ποιοτικός έλεγχος
επαφή
Ζητήστε ένα απόσπασμα
Αρχική Σελίδα ΠροϊόνταΦραγμός χάλυβα εργαλείων

AISI D3 / DIN EN X210Cr12 1.2080 Cold-Work Tool Steel Bar / Rod

AISI D3 / DIN EN X210Cr12 1.2080 Cold-Work Tool Steel Bar / Rod

Κίνα AISI D3 / DIN EN X210Cr12 1.2080 Cold-Work Tool Steel Bar / Rod προμηθευτής
AISI D3 / DIN EN X210Cr12 1.2080 Cold-Work Tool Steel Bar / Rod προμηθευτής AISI D3 / DIN EN X210Cr12 1.2080 Cold-Work Tool Steel Bar / Rod προμηθευτής AISI D3 / DIN EN X210Cr12 1.2080 Cold-Work Tool Steel Bar / Rod προμηθευτής

Μεγάλες Εικόνας :  AISI D3 / DIN EN X210Cr12 1.2080 Cold-Work Tool Steel Bar / Rod

Λεπτομέρειες:

Τόπος καταγωγής: Ηπειρωτική Κίνα
Μάρκα: UST
Πιστοποίηση: ISO 9001:2008
Αριθμό μοντέλου: ASTM D3

Πληρωμής & Αποστολής Όροι:

Ποσότητα παραγγελίας min: 3 μετρικοί τόνοι
Τιμή: USD 1200-3000 / Metric Ton
Συσκευασία λεπτομέρειες: Στην τυποποιημένη συσκευασία εξαγωγής και το πλόιμο υλικό με την ορθογώνια δέσμη μορφής, που καλύπτε
Χρόνος παράδοσης: 15-35 ημέρες
Όροι πληρωμής: L/C, T/T, D/A, D/P
Δυνατότητα προσφοράς: 1000 μετρικοί τόνοι το μήνα
Contact Now
Λεπτομερής Περιγραφή Προϊόντος
Υλικό: εργαλείο χάλυβα Πρότυπο: ΜΒ, ASTM, DIN, JIS
Βαθμός: D3 / 1.2080 Διάμετρος: 201000mm
Μήκος: Κάτω από 16 μέτρα Σχήμα: στρογγυλός φραγμός
Τεχνικές: Τραβηγμένος στο κρύο Καυτός - κυλημένος Ελασματοποιημένος εν ψυχρώ Σφυρηλατημένος Επιφάνεια: Μαύρος, φωτεινός, γυαλισμένος, ξεφλουδισμένος, ή κατόπιν αιτήματος
Υπερηχητική δοκιμή: 100% UT που περνούν Επεξεργασία: Ανοπτημένος ή αποσβημένος και μετριασμένος παρεχόμενος
Τέλος: Λοξευμένο, σαφές τέλος όπως απαιτείται Ποιοτική επιθεώρηση: SGS, BV κ.λπ.
Υπηρεσία: Η τέμνουσα υπηρεσία και η 3$η επιθεώρηση κομμάτων παρέχονται

INTRODUCTION

 

AISI D3 tool steel is a high carbon (Min 2.0 – Max , 2.35% C), with high chromium Cold work tool steel material (11-13% chrome metal), So The Tool Steel D3 metal material with Very Very high wear resisting properties, heat treatment can be reached to 54-62 HRc.

 

-D3 steel have nice wear resistant property. Even its hardness higher than D2 Steel. but toughness lower than AISI D2.

 

-D3 tool steel hardens in air with a low order of movement and offers a measure of corrosion resistance while polished. The high chromium percentage gives it nice corrosion-resisting properties in the hardened condition and low temperature.

 

-D3’s mechanical properties are very sensitive to heat treatment.

 

-D3 tool steel is provided in diameter round, flat bar, and square block.

 

 

APPLICATIONS

 

AISI D3 is used to cold work tools applications, it have well wear resistance, normal applications such as Blanking die and rolling die.

 

D3-Tool steels Typical applications as below:

 

Hunching die, molding die, stamping die, blades, heading tools, long punch, forming roller, grinding roll, master the tools, ball, punch, perplexing extrusion die, drawing die, compound die, thread rolling die, Shear Blades, Burnishing Tools, Knurls, and other wear parts.

 

Steel Grade 1.2080 Application Tool steel, Mold Steel
Shape Round Bar Standard GB, ASTM, DIN,JIS
Dimension Φ20-1000 mm; length below 16m Surface Black, Bright, Polished, Peeled
Technique Cold drawn; Hot rolled; Forged Ultrasonic Test 100% UT Passed

 

 

DELIVERY CONDITIONS

 

  Diameter (mm)
Cold drawn 10-100
Peeled 30-160
Grinded 10-600
Turned 130-1600
Hot Rolled 20-280
Hot Forged 130-1000

 

-EAF+(ESR) or EAF+LF+VD+(ESR)

-HOT rolled; Cold rolled; Forged; Cold Drawn

-Heat Treatment: Untreated, Annealing, N+T, Q+T

-Smelting: EAF+LF+VD (+ESR)

-Surface Finish: Black, Rough Machined, Peeled, Turned or as per given requirements

-UT 100% passed

-Cutting service provided

-Third Party inspection is acceptable (SGS, BV etc.)

 

EQUIVALENT GRADES

 

AISI/SAE DIN JIS GB
D3 1.2080 SKD1 Cr12

 

CHEMICAL COMPOSITION (%)

 

C Si Mn P S Cr V

2.00

2.35

0.10

0.60

0.10

0.60

0.030

0.030

11.00

13.50

1.00

 

 

PROCESSING

 

AISI D3 Steel Forged – Grade ASTM A681

First, For forging the AISI D3 tool steel should be heat to 700°C (1292°F) slowly and uniformly. Then heating to 1050-1100°C rapidly and Soak thoroughly. Below 900°C, no forging. After finished forging, slowly cool down in furnace. As necessary, stopping work when the temperature drops below 1700°F(926°C). The delivery state of AISI D3 steel should be annealed after forging always.

 

Heat Treatment for AISI D3 Tool Steel

AISI D3 steel alloy should be pre-heated very slowly to 815℃ (1500°F) and then temperature can be increased to 1010°C (1850°F). then keep at 1010°C (1850°F) for 20 to 45 minutes and air cool quenched.

 

Annealing of ASTM AISI-D3
Annealing for D3 tool steel material, that should be heat to 871°C to 898°C (1600 to 1650°F), then by slowly cooling at 6°C per hour or less in heat treatment furnace. Suitable precautions should be taken to prevent excessive carburization or deodorization.

 

Stress Relieving SAE D3 Steel Material
When need to relieve the strains of machine, slowly heating D3 steel grade to 566°C to 676°C (1050°-1250°F), soak equalize, and then cool in room (Air Strain Relieving).

 

Hardening AISI D3 Tool Steel
Slowly pre-heat to 750°C to 800°C and keep on the temperature until grade steel D3 material is unsure heated thoroughly. Then heat to 1000°C to 1040°C. Hold the D3 tool steel block at the hardening temperature until completely and uniformly heated.

 

Quenching of D3 steel works piece
ASTM D3 is an air Quenching steel. for avoid scaling and prevent decarburization of the workpiece surface, the vacuum furnaces or controlled atmosphere is recommended strongly. for avoid scaling and prevent decarburization of the work-piece surface, the vacuum furnaces or controlled atmosphere is advice strongly. If the furnaces are not available, packing harden, salt baths or packing the work-piece to stainless steel foil will provide some degree of surface protection in the hardening process. The Work-Parts should be cool to 65°C or room temperature, and then temper immediately.

 

Tempering of AISI Alloy Cold Work D3 Steel

The tempering temperature of material D3 steel varies, It should be according to the hardness demands. D3 steel can exercise 150 degrees C Rockwell C a hardness of 61-62 and 400 degrees C Rockwell C hardness 55-56.

 

AISI D3 / DIN EN X210Cr12 1.2080 Cold-Work Tool Steel Bar / Rod

 

What we can offer?

-We offer a wide range of steel products in a wide variety of dimensions and executions, according to the common international specifications or customize.

-Machining and heat treatment are available.

-Also, we advise you in choosing the right materials.

 

Shape Available

  • Solid round bar
  • Flat bar
  • Square bar
  • Hexagon bar
  • Block
  • Plate
  • Sheet
  • Wire rod
  • Strip

 

Our Advantages

  • High mechanical property and quenching, enable the surface share equal hardness after deal with it
  • Good polishing and low roughness
  • Making the heat-treatment to harden condition before using it
  • Competitive price
  • Fast production lead-time
  • All the material are inspected with 3 times to meet the highly standards
  • Pure steel quality & stable quality to be guarantee
 

OUR MAIN PRODUCTS ARE LISTED AS BELOW

 

AISI D3 / DIN EN X210Cr12 1.2080 Cold-Work Tool Steel Bar / Rod

 

Notes:

Available Size:
-Round: Dia. 20-1000 mm
-Flat: T. 10-120 mm x W. 60-810 mm
-Block: T. 80-1200 mm x W. 100-1600 mm

 

PAYMENT AND SHIPPING

 

1. Both T/T and L/C will be acceptable

2. Trade Terms: FOB, CIF, CFR

3. The delivery will be in 10-15 days if have stock; For customized items, the delivery will be negotiated by both parties

4. Shipping by sea freight from Shanghai Port (PRC) for Bulk orders, by airfreight or express for samples

 

COMPANY INFORMATION

 

Shanghai Unite Steel Trading Co., Ltd

We are committed to integrate engineering steel resources in china and serve the global engineering steel market. Our company has more than 15 years of experience in steel researching, production, managing and sales. And our team mostly are based on and worked in national famous steel enterprise.

In the aspect of resources and information, we have established cooperative and stronger relationship with nearly hundred enterprises, either state-owned or private owned in china.

What’s more, we have built long, deep and close business relationship with dozens of steel company, Sharing and holding equities with several steel enterprises. Because of the close cooperation with steel companies and our pioneering spirit, which can ensure us stay at the top competition, and ensure our customers get what they really want!

 

FAQ

 

Q: Are you a manufacturer or merely a trader?
A: We are group of companies and owned manufacturer bases and trading company. We specialized in special steel which include alloy structural steel and carbon steel and stainless steel, etc. All material are with high quality and competitive price.

Q: How do you guarantee the quality of your product?
A: Firstly, we can provide the certificates from the third party, such as TUV, CE, if you need. Secondly, we have a complete set of inspection system and every process is checked by QC. Quality is the lifeline of enterprise survival.

Q: Delivery time?
A: We have ready stock for most of material grades in our warehouse. If the material doesn't have stock, the delivery lead time is about 5-30 days after receiving your prepayment or firm order.

Q: What is the payment term?
A: T/T or L/C.

Q: Can we visit your company and factory?
A: Yes, warmly welcome! We can book the hotel for you before you come to China and arrange our driver to our airport to pick you up when you come.

 

CONTACT US

 

We are happy to answer your questions and make you an offer for these and other materials. Contact us now for more information.

 

Your Contact Person

Ms Chilli Ho

Phone/Wechat/Whatsapp +86-181-0187-5575

Skype: chilli.ho@outlook.com

Email: chilli.ho@shunitesteel.com

Στοιχεία επικοινωνίας
SHANGHAI UNITE STEEL TRADING CO., LTD

Υπεύθυνος Επικοινωνίας: Chilli.ho

Τηλ.:: +8618101875575

Στείλετε το ερώτημά σας απευθείας σε εμάς (0 / 3000)